| |
Prophet-H - Rate Table Programming Parameters
Note: Shaded areas (i.e. 005, 006, etc.) are programmed by the
distributor to meet customer requirements.
Go to:
Pricing Parameters (USED IN ALL RATE TABLES)
|
Location
|
Typical
Value
|
Description (See Setting Profit Controls page 3-39) |
|
001
|
1.00
|
Day Multiplier, Weekday. |
|
002
|
0.63
|
Evening Multiplier, Weekday. |
|
003
|
0.52
|
Night Multiplier, Weekday. |
|
004
|
1.00
|
Overtime Multiplier, Weekday. |
|
005
|
1.55
|
Surcharge, Weekday (guest room extensions) see 025 & 036
also. |
|
006
|
0.50
|
First Flat Rate (guest room extensions, type "F" in area code or
exchange position of this table to reference this flat rate). See Setting
Profit Controls page 3-39. |
|
007
|
0.01
|
Type of Table (0.01 = interstate, 0.02 = intrastate, 0.03 =
international, 0.04 = local, 0.00 = calls will not be accumulated as part of the
audit record. |
|
008
|
0.00
|
Flat Rate amount for all 7 digit dialed numbers to amount shown.
Applies to Rate Table 2 Only, charged to guest calls. CAUTION: Unless
ALL 7 digit numbers are local calls, set this location to 0.00. Ensure 092
in Rate Table 1 is set to 0.00. In V2.2 assigns a zero flat rate price to calls
when it is set to 0.01 |
|
009
|
0.20
|
Profit Multiplier (guest room extensions, 0.20 = 20%) |
|
010
|
0.03
|
Tax Multiplier (all extensions, 0.03 = 3%) |
|
011
(Ref)
|
T5
|
International Reference (points to International table, 0.00 = no
international rates). In this example tables 1 through 5 should be
programmed with profit markups and surcharges (the international table is
the last table factory loaded). |
|
012
(Ref)
|
1.12
|
First three digits of rate table serial number
|
|
013
(Ref)
|
0.34
|
Last two digits of rate table serial number (after the decimal
point). Serial number shown = 11234 |
|
014
(Ref)
|
0.02
|
Month of last rate table update (digits after the decimal point) |
|
015
(Ref)
|
0.95
|
Year of last rate table update (digits after the decimal point).
Date of last update shown = 02/95 |
|
016
|
0.46
|
Flat Rate Cost (Actual cost for admin. extensions) |
|
017
|
0.08
|
Day pricing start time, Weekday |
|
018
|
0.17
|
Evening pricing start time, Weekday |
|
019
|
0.23
|
Night pricing start time, Weekday |
|
020
|
0.00
|
Rate table Grace Period. Calls below this value will not be
reported. Caution: 0.05 = 5/10 = 30 seconds (normally left at 0.00) |
|
021
|
1.00
|
Day Multiplier, Weekend
|
|
022
|
0.63
|
Evening Multiplier, Weekend
|
|
023
|
0.52
|
Night Multiplier, Weekend
|
|
024
|
1.00
|
Overtime Multiplier, Weekend
|
|
025
|
1.55
|
Surcharge, Weekend (for Guest room extensions. See 005 &
036) |
|
026
|
0.00
|
Connect time - this duration is subtracted from the length of the
call to allow for call setup time and must be less than or equal to the value in
position 020. Normally set to 0.00. |
|
027
|
0.08
|
Day pricing start time, Weekend
|
|
028
|
0.17
|
Evening pricing start time, Weekend
|
|
029
|
0.23
|
Night pricing start time, Weekend
|
|
030
|
0.00
|
0.01 = multiply the value in location 900 (rate table 1) and 976
(rate table 2 controls all 976 numbers) by 100 (i.e. 900 value of 0.15 = $15.00
per minute). 0.00 = price as entered. |
|
032
|
0.00
|
0.01 = track unrated calls (rate table 1 controls this feature
for all tables). A value of "NO$" in area code/exchange locations will be
automatically changed to a value of "RATE?" (viewed by using <ctrl R> from
within the rate table) and the message "NO PRICE FOR FOLLOWING CALL. CALL FOR
SERVICE DURING NORMAL BUSINESS HOURS." will be printed as each new area code or
exchange is dialed (received as SMDR). 0.00 disables this feature. |
|
036
|
0.00
|
Additional surcharge (added to locations 005 & 025 when a
surcharge greater than $2.40 is needed) |
|
037
|
0.75
|
Second Flat Rate (guest room extensions, type "S" in area code or
exchange position of this table to reference this flat rate). See Setting
Profit Controls page 3-39. |
|
098
|
0.00
|
Operator Assist Cost (Actual cost of 0 plus calls for admin call
pricing rate table 1 only). |
System Operational Parameters & Control Flags (USED IN RATE TABLE 1 ONLY)
|
Location
|
Typical
Value
|
Description |
|
031
|
0.00
|
0.01 enables fill incomplete dialed numbers with "9" (for PBX's
that do not output enough digits especially when 10xxx or 10xxxx is used). 0.00
disables this feature. |
|
033
|
0.00
|
Increased administration table size for the Prophet-H10
only, this feature will increase the size of the administration table to
1000 extensions. To program the administration extensions, set Table 1 Location
033 to 0.02 and enter the extensions through the Prophet-H10 Main Menu
item ‘C’ (cross-reference). [Version 2.2] |
|
035
|
0.00
|
Minimum number of digits required in dialed number field for
record to be accepted (0.00 - 0.03 = 3 digits minimum) |
|
039
|
0.05
|
Alarm delay after printer deselect (0.00-1.28 = 0-128 seconds) |
|
089
|
0.00
|
Check before clearing call records (prompts before clearing) |
|
092
|
0.00
|
One-Plus Dialing Flag. Must be set to 0.00. |
|
188
|
0.00
|
0.01 = Run Monthly Report automatically on the first of the
month. 0.00 = disable automatic run of Monthly Report (See 095).
Ensure that the nightly audit report time is set to 00:01, not 23:59 so that the
Monthly report starts one minute into the new month avoiding calls made on the
first day of the new month. |
|
197
|
0.03
|
Number of hours before the SMDR timeout alarm occurs. 0.01 = 1
hour. The message "NO GUEST CALL REVENUE FOR xx HOURS. CALL FOR SERVICE".
mm/dd/yy hh:mm" is printed every hour along with a 10 second alarm (not active
between midnight and 7AM). 0.00 = off. |
Room Service/Revenue Center Parameters (USED IN RATE TABLE 1 ONLY)
|
Location
|
Typical
Value
|
Description |
|
040 |
0.06 |
1st digit to dial of access code
|
|
041 |
0.00 |
2nd Digit of access code
|
|
042 |
0.00 |
3rd Digit of access code (access code shown = 600) |
|
043 |
0.04 |
Room Number Length (Range: 1-4) |
|
044 |
0.00 |
Pass room status/revenue center records to PMS |
OCC Parameters (OCC's greater than 5 digits) (USED IN RATE TABLE 1 ONLY)
|
Location
|
Typical
Value
|
Description |
|
050 |
0.00 |
Point to last digit of 1st authorization code |
|
051 |
0.00 |
Value of last digit of 1st authorization code (ASCII) |
|
052 |
0.00 |
Number of digits to absorb before dialed number (OCC access +
auth. code) |
|
053 |
0.00 |
Point to last digit of 2nd authorization code |
|
054 |
0.00 |
Value of last digit of 2nd authorization code (ASCII) |
|
055 |
0.00 |
Number of digits to absorb before dialed number (OCC access +
auth. code) |
|
059 |
0.00 |
0.01 = Insert "1" in front of dialed number. Used if absortion
removes 1+ from area code calls. 0.00 = disabled. |
PMS Parameters (USED IN RATE TABLE 1 ONLY)
|
Location
|
Typical
Value
|
Description |
|
034
|
0.00
|
No. of Digits in Duration Field (0.00 = 4 digits, 0.01 = 5
digits) |
|
045
|
0.00
|
Round Up To Whole Minutes
|
|
046
|
0.00
|
HOBIC Style Sequence Number
|
|
047
|
0.00
|
Left Justify & Space Fill Room Number |
|
048
|
0.00
|
Put Dashes In Dialed Number Field
|
|
049
|
0.00
|
Number of Digits in the Dollar Field (0.00 = 4, 0.01 = 3) |
|
060
|
0.01
|
PMS Record Type (0.00 = Compressed, 0.01 = Expanded) |
|
061
|
0.01
|
PMS Attention Character Used. 0.01 = Enabled. |
|
062
|
0.05
|
Attention Character. 0.05 = use ASCII value 005 = ENQ.(a standard
value) |
|
063
|
0.06
|
Acknowledgement: Attention Character Rec'd 0.06 = use ASCII value
006 = ACK |
|
064
|
0.06
|
Acknowledgement: Character/Record Rec'd 0.06 = use ASCII value
006 = ACK |
|
065
|
0.21
|
Non-Acknowledgment: Record Not Rec'd 0.21 = use ASCII value 021 =
NAK |
|
066
|
0.02
|
Start-of-Text character for PMS record 0.02 = use ASCII value 002
= STX |
|
067
|
0.03
|
End-of-Text character for PMS record 0.03 = use ASCII value 003 =
ETX |
|
068
|
0.11
|
Time delay for PMS response after output of record in seconds.
0.11 = 11 secs |
|
069
|
0.07
|
Time delay between transmissions of attention character in
seconds. 0.07 = 7 secs. |
|
070
|
0.00
|
No decimal point in duration field flag. 0.01 = Enabled. |
|
071
|
0.01
|
Local flag location. 0.01 = place "L" at end of record. |
|
072
|
0.00
|
Pass wake up messages to PMS flag. 0.00 = disabled, 0.01 =
enabled. |
|
073
|
0.03
|
Number of retries before rejection. 0.03 = 1 original plus 3
retries (4 attempts). |
|
074
|
0.01
|
Suppress printer control characters. 0.01 = enabled, 0.00 =
disabled. |
|
075
|
0.01
|
Output a block check character at the end of record. 0.01 =
enabled, 0.00 = disabled. |
|
076
|
0.00
|
0.01 = Display dialed number digits for 0 plus calls. 0.00 =
disabled. |
|
077
|
0.01
|
Number of spaces between fields. 0.01 = one space. |
|
078
|
0.01
|
Flag international calls with an "F". 0.01 = enabled, 0.00 =
disabled. |
|
079
|
0.00
|
Fill dialed no. field with spaces. 0.01 = enabled, 0.00 =
disabled. |
|
087
|
0.00
|
Transmit administrative calls to PMS. 0.01 = enabled, 0.00 =
disabled. |
|
088
|
0.00
|
Drop local administrative calls. 0.01 = enabled, 0.00 = disabled. |
|
090
|
0.03
|
System port parity control code (0 = S, 1 = M, 2 = E, 3 = O) |
|
091
|
0.00
|
Size of Call Record Input Buffer in pages (1 page
» 3 calls). Keep this number
small to allow for call overflow to backup printer in the event of PMS failure
(approx 5 mins of call activity). |
|
093
|
0.01
|
0.01 = Suppress leading zeros in call pricing field. 0.00
disables this feature. |
|
095
|
0.00
|
0.00 = Display Report Menu.
0.01 = Run Daily
Profit and Admin Call Report only (no menu option) Monthly Report cannot be run
manually (See 188). Error in
manual |
|
096
|
0.00
|
System port - number of stop bits (0.00 = 1, 0.01 = 2) |
|
187
|
0.00
|
Pass "S" flagged record (special) to PMS when access code
indicated is dialed. |
|
189
|
0.00
|
0.01 = Do not post zero priced calls. 0.00 = Post zero priced
calls. |
|
198
|
0.10
|
Number of minutes before PMS attention timeout. 0.10 = if no
acknowledgement (ACK) within 10 mins, switch to single attempt then pass
unacknowledged call to backup printer. 0.00 = disabled, |
|
199
|
0.01
|
Number of hours before PMS timeout alarm. 0.01 = If PMS fails to
respond within 1 hour, a two second alarm sounds followed by the message "CALLS
NOT POSTING TO GUEST FOLIOS. CALL FOR SERVICE.". 0.00 = disabled, |
Diagnostic Mode (USED IN RATE TABLE 1 ONLY)
|
Location
|
Typical
Value
|
Description |
|
080 |
0.00 |
0.01 = See-Thru Mode and passes SMDR output to SYSTEM port.
Readable data confirms SMDR baud rate match. Normal processing is disabled.
Resetting the Prophet automatically sets this value to 0.00. |
|
081 |
0.00 |
0.01 = Accepted Call Diagnostics. Call processing is normal.
Resetting the Prophet automatically sets this value to 0.00. Location 080 must
equal 0.00. See Diagnostics format page 4-15. |
|
082 |
0.00 |
0.01 = Rejected Call Diagnostics. Call processing is normal.
Resetting the Prophet automatically sets this value to 0.00. Location 080 must
equal 0.00. See Diagnostics format page 4-15. |
|
083 |
0.00 |
0.01 = Dropped Call Diagnostics. Call processing is normal.
Resetting the Prophet automatically sets this value to 0.00. Location 080 must
equal 0.00. See Diagnostics format page 4-15. |
|
084 |
0.00 |
0.01 = Rejected Room Status/Revenue Center Call Diagnostics. Call
processing is normal. Resetting the Prophet automatically sets this value to
0.00. Location 080 must equal 0.00. |
PBX Operational Parameters (USED IN RATE TABLE 1 ONLY)
|
Location
|
Typical
Value
|
Description |
|
085 |
0.00
|
2-Line SMDR record (MARK II format). 0.00 = single line format
(default) |
|
094
|
0.00
|
Call Record Duration Type(0.00 = duration, 0.01 = start/end) |
|
097
|
0.00
|
SMDR Time Out (clear buffer after each call). 0.00 = do not clear
buffer (default) |
|
100
|
|
Value of Start Character in Input Record (ASC II) |
|
101
|
|
Value of Terminating Character in Input Record (ASC II) |
|
102
|
|
Length of Minimum Call Record |
|
103
|
|
Pointer: To Location of Call Record Test Character |
|
104
|
|
Value of Call Record Test Character (ASCII) |
|
105
|
|
Pointer: To Call Duration - Hours/Tens (if any) |
|
106
|
|
Pointer: To Call Duration - Minutes/Hundreds (if any) |
|
107
|
|
Pointer: To Call Duration - Minutes/Tens |
|
108
|
***
|
Pointer: To Call Duration - Minutes/Tenths (if any) |
|
109
|
***
|
Pointer: To Call Duration - Seconds/Tens (if any) |
|
110
|
|
Pointer: To Start Time of Call |
|
111
|
|
Pointer: To Beginning of Access Digits Field |
|
112
|
|
Pointer: To End of Access Digits Field |
|
113
|
|
Pointer: To Beginning of Dialed Number Field |
|
114
|
|
Pointer: To End of Dialed Number Field |
|
115
|
|
Pointer: To Time of Call Type
|
|
116
|
|
Pointer: To Duration - Thousands of Minutes |
|
117
|
|
Pointer: To Beginning of Station Number Field |
|
118
|
|
Pointer: To End of Station Number Field |
|
119
|
|
Value of Start Character for Pass-Through Message (ASC II) |
|
120
|
|
Pointer: To Duration Start Time - Hours/Tens
|
|
121
|
|
Pointer: To Duration Start Time - Minutes/Tens
|
|
122
|
|
Pointer: To Duration Start Time - Seconds/Tens (if any) |
|
123
|
|
Pointer: To Duration Start Time - Minutes/Tenths (if any) |
|
124
|
|
Pointer: To Duration End Time - Hours/Tens
|
|
125
|
|
Pointer: To Duration End Time - Minutes/Tens
|
|
126
|
|
Pointer: To Duration End Time - Seconds/Tens (if any) |
|
127
|
|
Pointer: To Duration End Time - Minutes/Tenths (if any) |
|
128
|
|
Pointer: To Duration Start Time Type
|
|
129
|
|
Pointer: To Duration End Time Type
|
|
132
|
|
Value for 2nd call record test character (ASCII) |
|
133
|
|
Pointer: To test character of call record to reject |
|
134
|
|
Value of test character of call record to reject |
Dialed Number Translation (USED IN RATE TABLE 1 ONLY)
|
056
|
0.00
|
V2.2 and above. This feature is useful in applications where the 1+ is stripped
from the dialed number received by the Prophet-H. Location 056 , when not set to
0.00, specifies the maximum number of digits for a home area code call (Table
2). Calls with digits in excess of the value of 056 will start pricing in Table
1. Typical settings for non-1+ dialing would be 0.07, 0.08 & 0.09. Both 1+ and
non-1+ will be processed.
example: Set 056 = 0.09 then all calls, 10 digits or more, will go to Table 1
for initial processing. Default for 056 = 0.00 when digit count not required.
|
|
140 |
0.00 |
First dialed number check string: 1st digit (ASCII) |
|
141
|
0.00
|
First dialed number check string: 2nd digit (ASCII) |
|
142
|
0.00
|
First dialed number check string: 3rd digit (ASCII) |
|
143
|
0.00
|
First dialed number check string: 4th digit (ASCII) |
|
144
|
0.00
|
First dialed number check string: 5th digit (ASCII) |
|
145
|
0.00
|
First dialed number exchange string: 1st digit (0=end) |
|
146
|
0.00
|
First dialed number exchange string: 2nd digit (0=end) |
|
147
|
0.00
|
First dialed number exchange string: 3rd digit (0=end) |
|
148
|
0.00
|
First dialed number exchange string: 4th digit (0=end) |
|
149
|
0.00
|
First dialed number exchange string: 5th digit (0=end) |
|
150
|
0.00
|
Second dialed number check string: 1st digit (ASCII) |
|
151
|
0.00
|
Second dialed number check string: 2nd digit (ASCII) |
|
152
|
0.00
|
Second dialed number check string: 3rd digit (ASCII) |
|
153
|
0.00
|
Second dialed number check string: 4th digit (ASCII) |
|
154
|
0.00
|
Second dialed number check string: 5th digit (ASCII) |
|
155
|
0.00
|
Second dialed number exchange string: 1st digit (0=end) |
|
156
|
0.00
|
Second dialed number exchange string: 2nd digit (0=end) |
|
157
|
0.00
|
Second dialed number exchange string: 3rd digit (0=end) |
|
158
|
0.00
|
Second dialed number exchange string: 4th digit (0=end) |
|
159
|
0.00
|
Second dialed number exchange string: 5th digit (0=end) |
|
160
|
0.00
|
Third dialed number check string: 1st digit (ASCII) |
|
161
|
0.00
|
Third dialed number check string: 2nd digit (ASCII) |
|
162
|
0.00
|
Third dialed number check string: 3rd digit (ASCII) |
|
163
|
0.00
|
Third dialed number check string: 4th digit (ASCII) |
|
164
|
0.00
|
Third dialed number check string: 5th digit (ASCII) |
|
165
|
0.00
|
Third dialed number exchange string: 1st digit (0=end) |
|
166
|
0.00
|
Third dialed number exchange string: 2nd digit (0=end) |
|
167
|
0.00
|
Third dialed number exchange string: 3rd digit (0=end) |
|
168
|
0.00
|
Third dialed number exchange string: 4th digit (0=end) |
|
169
|
0.00
|
Third dialed number exchange string: 5th digit (0=end) |
|
170
|
0.00
|
Fourth dialed number check string: 1st digit (ASCII) |
|
171
|
0.00
|
Fourth dialed number check string: 2nd digit (ASCII) |
|
172
|
0.00
|
Fourth dialed number check string: 3rd digit (ASCII) |
|
173
|
0.00
|
Fourth dialed number check string: 4th digit (ASCII) |
|
174
|
0.00
|
Fourth dialed number check string: 5th digit (ASCII) |
|
175
|
0.00
|
Fourth dialed number exchange string: 1st digit (0=end) |
|
176
|
0.00
|
Fourth dialed number exchange string: 2nd digit (0=end) |
|
177
|
0.00
|
Fourth dialed number exchange string: 3rd digit (0=end) |
|
178
|
0.00
|
Fourth dialed number exchange string: 4th digit (0=end) |
|
179
|
0.00
|
Fourth dialed number exchange string: 5th digit (0=end) |
Pass Wake Up & Special Messages (USED IN RATE TABLE 1 ONLY)
|
Location
|
Typical
Value
|
Description |
|
130
|
|
Pointer: To 1st Message Test Character
|
|
131
|
|
Value of Message Test Character (ASCII) |
|
180
|
0.00
|
Pointer: To 2nd message test character |
|
181
|
0.00
|
Value of message test character (ASCII) |
|
182
|
0.00
|
Pointer: To 3rd message test character |
|
183
|
0.00
|
Value of message test character (ASCII) |
|
184
|
0.00
|
Pointer: To check character |
|
185
|
0.00
|
Value of check character (ASCII) |
|
186
|
0.00
|
Value of exchange character (ASCII) |
Telephone Command Reporting (USED IN RATE TABLE 1 ONLY)
|
Location
|
Typical
Value
|
Description |
|
190
|
0.02
|
Telephone access code: 1st numeric value (0.00-0.09) |
|
191
|
0.00
|
Telephone access code: 2nd numeric value (0.00-0.09) |
|
192
|
0.00
|
Telephone access code: 3rd numeric value (0.00-0.09) (access code
shown = 200) |
|
193
|
0.00
|
Value of 1st character for reporting extension (ASCII). See
Apx K for ASCII values |
|
194
|
0.00
|
Value of 2nd character for reporting extension (ASCII) . See
Apx K for ASCII values |
|
195
|
0.00
|
Value of 3rd character for reporting extension (ASCII) . See
Apx K for ASCII values |
|
196
|
0.00
|
Value of 4th character for reporting extension (ASCII) . See
Apx K for ASCII values
(authorized admin extension example = 1700=(0.49+0.55+0.48+0.48) |
Unused Locations (USED IN RATE TABLE 1 ONLY)
|
Location
|
Typical
Value
|
Description |
|
000
|
0.00
|
Unused. |
|
038
|
0.00
|
Unused. |
|
056 |
0.00 |
Unused. (Below V2.2) |
|
057-058
|
0.00
|
Unused. (Except in V1.0.8 & V1.0.9, 058 must equal 0.01) |
|
135-139
|
0.00
|
Unused. |
|
086
|
0.00
|
Unused. (Except in V1.0.8 & V1.0.9, 058 must equal 0.01) |
|
099
|
0.00
|
Unused. |
Common Area Code and Exchange Modifications (RATE TABLE SPECIFIC AS NOTED)
|
Location
|
Typical
Value
|
Description |
|
411
|
FLAT
|
Use in rate table 2 only. Type F to point at the value in 006 or
S to point to the value in 037. |
|
555
|
FLAT
|
Use in ALL rate tables. Type F to point at the value in 006 or S
to point to the value in 037. |
|
611
|
FLAT
|
Use in Rate table 2 only. Type F to point at the value in 006 or
S to point to the value in 037. |
|
800
&
888
|
DROP
|
Use in Rate table 1 only. Type D to Drop these calls with no
charge. |
|
900
|
***
|
Use in Rate table 1 only. Type the per min rate to charge. See
location 030 in System Parameters to multiply this value by 100. |
|
911
|
NO$
|
Use in Rate table 2 only. Type N to flag this call with a NOT
INITIALIZED message. |
|
950
|
DROP
|
Use in Rate table 2 only (OCC access). Type D to Drop these calls
with no charge. |
|
976
|
***
|
Use in Rate tables 2-J. Type the per min rate to charge. See
location 030 in System Parameters to multiply this value by 100. |
|
|
|